Double Up – Boiler Retrofit in Halifax
April 29, 2026
By Thomas Renner
Halifax apartment complex retrofit replaces two cast iron boilers with four modulating condensing units for greater efficiency and redundancy.

(photos courtesy City Wide Mechanical)
For some heating projects, the hardest part of the job isn’t getting the new system in. It’s getting the old system out.
The team at City Wide Mechanical in Halifax found such an assignment in retrofitting the heating system for an 86-unit, four-story apartment complex. The project required eight weeks to complete and included the removal of two extremely heavy boilers and an elaborate plan to minimize inconvenience for tenants while maximizing system efficiency.
Matt Austen, project manager, said the installation required splitting the system in half, and the team replaced aging inefficient cast iron boilers with four modulating condensing units.
“We did the project in two stages,’’ Austen said. “That ensured that the in-floor heat sections of the building could have their own dedicated low temperature boilers. The low-temp boilers are far more efficient than heating the whole building at high temp and mixing it down.”
INEFFICIENT SYSTEM
Austen’s top priority for the new system was efficiency. The existing system included the two aging boilers that were prone to breakdowns and set up in a design that wasted energy.
“The first floor and domestic hot water for the building were all done at high temperature,’’ Austen explained. “They were mixing it down to do the upper three floors, which is inefficient.”
The City Wide team replaced the old cast iron boilers with modern modulating condensing boilers. The install required careful planning so that residents maintained thermal comfort as workers completed the retrofit. Austen said his team tackled the project in two stages.
“Since both of the (original) gas boilers were tied into the same system, we needed to remove one of the gas boilers, install two new boilers and tie them into the system temporarily. But we also needed to take over the load for the entire building.” Austen’s crew then moved on to the second stage of the project, removing the second boiler and installing two more of the higher-efficiency units.
Finally, City Wide needed to shut the entire system down temporarily to split the system in half to improve overall efficiency. “We got all the program controls working and created two separate systems with their own expansion tanks,’’ Austen said. “Essentially, there are now two separate automated heating systems in the same mechanical room, rather than one.”
The benefit of the new system is redundancy and automation through controls that combine to deliver reliable and consistent heat and hot water.
“We wanted redundancy on both sides,’’ Austen explained. “That’s why we went from two boilers to four. If we ever lost one for any reason, we would still have something working.”
OUT WITH THE OLD
The task of removing the original cast iron boilers (likely installed more than two decades ago) proved laborious and time-consuming. “Some building owners won’t do it because the removal cost is so expensive, and each section is six to 10-feet long, maybe around 500 pounds,’’ Austen said. “We took sledgehammers to break them apart.”
The boiler breakdown was just the beginning. Workers then needed to haul away the sectional pieces from the basement. “Removing those big cast iron sectionals is a giant undertaking, especially if there are stairs or an elevator involved,’’ Austen said. “There’s just so much weight.”
Cast iron boilers were commonplace in multi-residential projects decades ago, but more building owners are swapping out those units for energy efficient condensing boilers.
“Cast iron sectionals can crack in half, normally because of temperature differences,’’ Austen noted. “Once they crack, they’re expensive to replace. That’s normally the straw that breaks the camel’s back with the building owner.”
Austen has seen owners repair older boilers only to find they need repairs again the following year. “They are realizing they can install new condensing boilers for the same cost as repairing the cast iron boiler.”
City Wide also had to ensure proper venting, which created several challenges.
“Since we could not shut the building down, we had to temporarily vent the first two boilers out the side of the building while we dropped four vents down the existing clay lined chimney,’’ Austen explained. “This prevented a prolonged shutdown. Once the vertical venting from Centrotherm was installed, we connected them to the existing venting we had sidewall vented.”
MODERN BOILERS
The crew installed four NTI TFTN600 boilers, which have a 97.8 thermal efficiency and heating capacity of 585 MBH. The units included remote monitoring and diagnostics, a setup wizard and built-in zone control for up to three heating zones plus domestic hot water.
“The two boilers are cascaded together with a 10-1 turndown ratio and are far more efficient than the existing equipment,” Austen said. “We get a lot more output, and we also get increased redundancy.”
Austen also said the ease of setting up the units makes them ideal for retrofit projects. “For multi-story residential and commercial buildings, the controls on these units for wiring and programming are pretty simple,’’ Austen said.
The units are also much easier to physically handle than the heavy cast iron boilers. The heat exchanger at the heart of the boiler includes a 10-year warranty, which is critical for building owners.
The boilers include an outdoor reset on the high and low temperature systems. Austen installed Grundfos pumps with strainers, which help protect the pumps and boilers from iron and debris.
CONDENSING CONVERSIONS
The retrofit by City Wide is just one example of a trend in Canada to move towards modern condensing technology.
“These units run all day and all night,’’ Austen said. “Everyone relies on it. When the heat and hot water go down, the landlord is the first person the tenant is going to call. It’s expensive if we have to go out there in the winter. We’ll try to nudge the building owners along and convince them to convert to a condensing boiler. It’s an important part of their building.” <>
